Duerkopp Adler 609 Instruction Manual

609SpezialnähmaschineBetriebsanleitungInstruction manualPostfach 17 03 51, D-33703 Bielefeld • Potsdamer Straße 190, D-33719 BielefeldTelefon +49 (0)

6. Operation6.1 Threading the needle threadCaution: Danger of injury!Turn off the main switch !The needle thread may only be threaded with the sewing

Fig. A Correct thread loop in the center of thematerialFig. B Needle-thread tension too loworhook-thread tension too highFig. C Needle-thread tension

6.4 Winding on the hook thread–Thread the hook thread as shown in the picture above.–Fit the bobbin 3 on the bobbin-winder shaft 2.–Wind approximately

6.5 Fitting the hook-thread bobbinCaution: Danger of injury!Turn off the main switch !The hook-thread bobbin may only be changed with the machineswitc

6.6 Adjusting the hook-thread tensionAdjusting the braking spring 1The braking spring 1 prevents the idle motion of the bobbin when themachine halts o

6.7 Inserting and changing the needleCaution: Danger of injury!Turn off the main switch !The needle may only be changed with the sewing machineswitche

6.8 Adjusting the sewing foot strokeCaution: Danger of injury!Turn off the main switch !The sewing foot stroke may only be adjusted with the machinesw

6.9 Adjusting the sewing foot pressure–Loosen the counter nut 1.–The required sewing foot pressure can be adjusted with screw 2.To increase the sewing

7. Control unit and operating panelATTENTION!These operating instructions give the key functions and describe howoperator-level parameter values are c

7.2.1 Control unit keys (sewing mode)If the operating panel C300 is connected, the setting done through theoperating panel will have higher priority t

Alle Rechte vorbehalten.Eigentum der Dürkopp Adler AG und urheberrechtlich geschützt. Jede, auch auszugsweiseWiederverwendung dieser Inhalte ist ohne

7.2.2 Operating panel keys (Type C300)Explanation of the important function keys for the operation of theclass 609:Initial bartack.For the class 609,

7.2.3 Changing the parameter valuesFor checking purposes or after a reset the parameter values must beset according to the parameter sheet (Part No. 9

Operating and function sequence:Sew ing process Operation / explanationPrior to sew ingStarting position - Pedal in rest position- The machine is at a

Sewing continuous seamwithout attaching stitches - Prerequisite: on the operating panelthe key has its LED OFF- Prerequisite: on the operating panelth

Notes:22

9. MaintenanceCaution: Danger of injury!Turn off the main switch !Maintenance may only be carried out with the machine switched off!Maintenance work m

9.2 LubricationCaution: Danger of injury!Oil can cause skin eruptions.Avoid protracted contact with the skin.In the event of contact, thoroughly wash

ForewordThis instruction manual is intended to help the user to become familiarwith the machine and take advantage of its application possibilities in

General safety instructionsThe non-observance of the following safety instructions can cause bodily injuries or damages to the machine.1. The machine

Content page:Preface and general safety instructionsPart 1: Operating Instructions class 609(Edition 10/2007)1. Product description ...

1. Product descriptionThe DÜRKOPP ADLER 609 is a single needle double lockstitchcylinder arm machine for attaching and basting works on jackets,coats,

As manufacturers of industrial sewing machines we proceed on theassumption that personnel who work on our products will havereceived training at least

5. Technical dataRated noise value Lc:Workplace-related emission value in accordance with DIN45635-48-A-1-KL2Lc = xx dB (A)Class: 609Stitch length: ma