Duerkopp Adler 550-16 User Manual

Contents Page:Preface and General Safety InformationPart 1: Operating Instructions Class 550-16-231. Product Description ...

4.6 Changing the Hook Thread BobbinCaution Risk of Injury !Turn the main switch off .Change the hook thread bobbin only with the machine turned off.Re

4.7 Setting the Hook Thread TensionCaution Risk of Injury!Turn the main switch off .Set the hook thread tension only with the machine turned off.Half

4.8 Changing the NeedleCaution Risk of Injury!Turn the main switch off .Change the needle only with the sewing machine turned off.–Loosen screw 1.–Pus

4.9 Sewing Foot LiftThe sewing foot can be lifted pneumatically by operating the pedal 4.Pneumatic sewing foot lift (pedal)–Step half back on the peda

4.10 Arresting the Sewing Foot in the High PositionThe pneumatically raised sewing foot can be arrested in the highposition with button 3 (e.g. for wi

4.12 Stroke Height of the Sewing Foot during LiftingThe stroke height of the sewing foot during lifting can be limited by theknurled nut 1 (max. 3 mm)

4.14 Knee SwitchWith the knee switch 1 one moves from one program step to the next inthe sewing programs.–Press the knee switch.The next program step

5. Operating the Controls 550-16-23The 550-16-23 is equipped with programmable controls. The functionscan be programmed via the keypad.5.1 Manual Sewi

5.1.4 Bartack InversionThe bartack set in the parameters (see Part 4: ProgrammingInstructions) is inverted (suppressed) by simultaneously pressing the

5.2.1.2 Program Selection via MenuIf the program number is unknown, all programs can be run throughsequentially in the following manner.Order of opera

Contents Page:5.3.3 Saving Changes in the Program ... 245.3.4 Deleting a Program ...

5.2.2 Changing Fullness ValuesFor the adaption to differing types of material with the program step,the fullness values can be changed via the “0"

5.3 Programmable FunctionsThe machine settings described in the following are saved in memorywith each program.5.3.1 Generating a New ProgramThe gener

5.3.2 Temporary Changes in a StepEvery function in a step can be changed as required. This changeapplies only for this program run. When the step is e

6. SewingSewing cycle Operation / RemarksV Before the start of sewingInitial positionPositioning the material atthe seam beginning- Pedal in rest posi

7. Maintenance7.1 Cleaning and CheckingCaution Risk of Injury!Turn the main switch off .Conduct maintenance work only with the machine switched off.Th

Maintenance work Explanantion Serviceto be carried out hoursPneumatic System- Check water level in thepressure regulator.- Clean the filter element.-

7.2 LubricationCaution Risk of Injury !Oil can cause skin rashes.Avoid longer skin contact.After contact wash yourself thoroughly.ATTENTION !The handl

1. Product DescriptionThe Dürkopp Adler 550-16-23 is a configured sewing station for thesewing-on of sleeves.The workstations are equipped with a sing

3. Technical DataNoise Workstation-specific emission value to DIN 45635-48-A-1-KL2Cl. 550-16-23 Lc = 79 dB (A)Stitch length: 4,4 [mm]Number ofstitches

4. Operation4.1 Threading the Needle ThreadCaution Risk of Injury !Turn the main switch off !Thread the needle thread only with the sewing machine tur

Illus. A: Correct thread interlacingin the middle of the materialIllus. B: Needle thread tension too loworhook thread tension too highhighIllus. C: Ne

4.2 Setting the Needle Thread TensionPre-tensionWith open main tension 3 a slight residual tension on the needle threadis necessary. The residual tens

4.4 Setting the Thread RegulatorCaution Risk of Injury !Turn the main switch off .Set the thread regulator only with the sewing machine turned off.The

4.5 Winding the Hook Thread–Slip the bobbin onto the bobbin winder 2.–Pull the thread through the guide 3 and the tension 4.–Wind the thread clockwise