Duerkopp Adler 887 Instruction Manual

SpezialnähmaschineBetriebsanleitung887Postfach 17 03 51, D-33703 Bielefeld • Potsdamer Straße 190, D-33719 BielefeldTelefon +49 (0) 521 / 9 25-00 • Te

5. Technical dataStitch type double lockstitch 301Needle system 134LR, 134 KKLR, 134, 134 DFoot lifting with a hand lever 6 mmFoot lifting with a knee

6. Machine operation6.1 Threading the needle threadCaution! Risk of injury!Turn off the main switch.The needle thread may only be threaded with the se

6.3 Inserting the bobbin and threading the hook threadCaution! Risk of injury!Turn off the main switch.The hook-thread bobbin may only be changed with

6.4 Adjusting the thread tension6.4.1 Adjusting the hook thread tensionCaution! Risk of injury!Turn off the main switch.The hook thread tension may on

6.4.2 Adjusting the needle thread tensionSupplementary tensioner adjustment (1)–Adjust the supplementary tensioner (1) so that it has the lowesttensio

Correct thread interlacing in the centerof the materialNeedle-thread tension too loworhook-thread tension too highNeedle-thread tension too highorhook

6.6 Adjusting the thread regulatorThe thread regulator (2) controls the quantity of needle thread requiredfor stitch formation.The thread regulator mu

6.7 Needle changeCaution! Risk of injury!Turn off the main switch.The needle may only be changed with the sewing machine switchedoff.–Draw the lever (

6.8 Lifting and folding the roller presserLifting the roller presser with a hand lever–Lift the roller presser by the lever turning (1) in the arrow d

Roller presser folding–Lift the roller presser with the hand lever.–Lift the roller presser by pressing in the signed direction.Caution! Risk of injur

Alle Rechte vorbehalten.Eigentum der Dürkopp Adler AG und urheberrechtlich geschützt. Jede, auch auszugsweise Wiederverwendungdieser Inhalte ist ohne

6.10 Reverse sewing (Backtacking)Backtacking with a hand lever–Press the lever (1) downwards. As long as the reverse feedlever (1) is pressed down, th

6.11 Setting the stitch length–Turn the button (1) so that the number (2) indicating the requiredstitch length in mm is opposite the mark (3).6.12 Sta

6.13 Controlling the machine equipped with a positioning motor6.13.1 By a control pedalThe pedal position is scanned by a sensor distinguishing 16 lev

6.13.2 By a key panelKey Function1 Manual bactackingWhen the key is pressed during the sewing, the sewn material is fed backwards.2 Needle positioning

7. Positioning motor Efka DC1600/DA82GA7.1 GeneralFor a detailed description of the control unit, please consult theenclosed current issue of the oper

9. Positioning drive Efka DC1550/DA321G9.1 GeneralFor a detailed description of the control unit, please consult theenclosed current issue of the oper

10. Sewing with machine with positioning motor (drive)10.1 Machine automatic functionsThe machine has the below functions which are automaticallyperfo

10.2 Example of machine operation at sewingPre-selection:Needle down at machine stopping in seamStandard bartacksDouble initial bartackDouble end bart

11. Maintenance11.1 Cleaning and checkingCaution! Risk of injury!Maintenance may be carried out only with the machine switched offand the motor stoppe

Maintenance work Explanation Operatingto be carried out hours- Clean the oil sump. Cleaning the oil sump (1) for example witha special vacuum cleaner.

ForewordThis instruction manual is intended to help the user to become familiarwith the machine and take advantage of its application possibilities in

Maintenance work Explanation Operatingto be carried out hoursPneumatic system- Check water level inpressure regulator.- Clean filter cartridge.- Check

11.2 LubricationCaution: danger of injuryOil can cause skin eruptions.Avoid protracted contact with the skin.In the event of contact, thoroughly wash

Notes:30

GBContents Page:Part 2: Installation Instructions Class 8871. Scope of delivery... 32. General and transport

2

1. Scope of deliveryWhat items are supplied depends on your order.Prior to setting up, please check that all the required parts are present.This descr

2. General and transport packingCaution:The special sewing machine must be set up by trained specialistpersonnel.If the special sewing machine you hav

3.2 Assembly of stand table top3.2.1 Assembly of stand table top in the machine with the motor on the stand table top–Turn the table top (1) upside do

3.2.2 Assembly of stand table top with the motor on the machine head (direct drive)–Turn the table top (1) upside down.–Screw the electric cable chann

3.3 Setting the working height–The stand height is adjustable between 750 and 900 mm.–Loosen the screws (1).–Set the required table top height and mak

General safety instructionsThe non-observance of the following safety instructions can cause bodily injuries or damages to the machine.1. The machine

84. Assembling the machine head4.1 Fitting the machine head–If the sewing machine is equipped with a motor on the table top,insert the machine head (1

4.2 Fitting and tensioning the V-beltThis paragraph applies only to the machines with the motor on thetable top.–Mount the V-belt pulley (1) and the V

4.3 Fitting the belt guards–Disassembly the hand wheel (1).–In the machines with the motor on the table top mount the guard (2)on the machine head (th

4.4 Setting the pedal–Adjust the side position of the pedal (1) so that its center lies on theneedle axis.–Adjust the draw rod (2) so that the foot ax

4.5 Installation of knee lever and oil pump pipe–Tilt the machine head (1).–Lift the foot with the hand lever.–Slide the shaft (3) in the lever (4).–S

4.6 Fitting the proximity switch–The proximity switch (1) is mounted to certain positioning motors(drives) only. In that case it is part of the drive

4.7 Installation of connecting cable, control panel and sewing diode lamp on themachine head–The connecting cable (1) is supplied with every machine w

5. Electrical connectionThe machine drive is supplied from the low voltage network.Caution!All work on the electrical equipment of this special sewing

5.1.1 Sewing lamp transformer connection to network voltageCaution! Risk of electric current injury!The sewing lamp transformer is not switched off by

5.2 EarthingThe earthing cable (1) is included in the accessory package of themachine head.–Connect the earthing cable (1) to the plug (2) (already sc

Contents Page:Preface and general safety instructionsPart 1:(Edition 06/2008)1. Product description ... 52. D

5.3 Connection of machine head electric equipment to driveThe electric equipment on the machine head is described in chapter4.6 and 4.7. Its connectio

–Connect the connecting cable to the connector (1).–Connect the control panel to the connector (2).–Connect the synchronizer to the connector (3).Note

6. Setting of positioning motor (drive)The function of the positioning motor (drive) is defined by its program,drive parameter setting, and the machin

6.1.3 Setting machine-specific parameters6.1.3.1 DC1600/DA82GA driveThe value of the following parameters must beParameter Orig. value New value Param

6.1.3.3 DC1550/DA321G driveParameter change for machines with gear rate of 28/28 teethParameter Original value New value Parameter description290* 0 3

6.2 Setting of machine positioning6.2.1 Position definitionPosition 1The needle is down at the stopping in the seam. The angle 225° is onthe hand whee

6.2.4 Setting of machine positioning with VD552/6F82FA driveThe synchronizer contains one internal disc with increments(generator) for the speed regul

6.2.5 Checking of set positions1st position–Switch on the network switch.–Tread the pedal forwards shortly and release. The machine isstopped in the 1

Änderung der technischen DokumentationModification of the technical documentationModification de la documentation tecniqueModificación de la documenta

Contents Page:10. Sewing with machine with positioning motor (drive)10.1 Machineautomaticfunctions... 2410.2 Exam

Additional nstructionsMachines with ntegrated otor887

About this manualAdditional instructions: Machines with integrated motor - version 00.0 - dated 10/2012 11 About this manualThese additional instructi

ECO-machinesAdditional instructions: Machines with integrated motor - version 00.0 - dated 10/2012 23 ECO-machines3.1 OperationFig. 1: Switching ECO-m

ECO-machinesAdditional instructions: Machines with integrated motor - version 00.0 - dated 10/2012 3Fig. 2: Operator settings with ECO-machinesSetting

CLASSIC-machinesAdditional instructions: Machines with integrated motor - version 00.0 - dated 10/2012 44.1 OperationFig. 3: Switching CLASSIC-machine

CLASSIC-machinesAdditional instructions: Machines with integrated motor - version 00.0 - dated 10/2012 5Fig. 4: Switching the sewing light on and sett

CLASSIC-machinesAdditional instructions: Machines with integrated motor - version 00.0 - dated 10/2012 6. Sewing light connectionThe PCB plug connec

DÜRKOPP ADLER AGPotsdamer Str. 19033719 BielefeldGermanyPhone +49 (0) 521 925 00E-Mail: [email protected] to de

1. Product descriptionDürkopp Adler 887 is a special sewing machine for universal use.•It is a flatbed double-lockstitch machine.•The machine has a do

3. Subclasses and sewing equipment3.1 SubclassesClass and subclass Needle Stitch Machine Hook Trimmingnumber length control andbacktacking1 needle, ho

4. Optional equipmentOrder number Optional equipment0888 220334 Roller presser Æ 25 mm knurled0888 220344 Roller presser Æ 25 mm smooth0888 220354 Rol